Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

Complete shallow bowl 190mm chrome headlight unit. Includes a pilot / parking light. A shallow bowl makes it especially suitable for mounting on Moto Guzzis underneath the instruments

Homologated for road use.

Supplied complete with H4 bulb, pilot light and four short wires (without connectors). This headlight will fit fairing cowling FAA99575 for Le Mans 1 conversions if trim strip is not fitted to inside edge of fairing. NB mounting holes will need drilling out to 10mm if fitting T3 type indicator stems

 1 in stock

Round 12v two pin flasher relay with warning buzzer, reduces risk of indicators being left on.

Includes mounting rubber

 1 in stock

 17750520 GU17750520 17 75 05 20
 1775 0520 1775.0520 17.75.05.20

Combined regulator rectifier to replace separate items on Bosch equipped models. See our wiring instructions page for help installing this reg/rec.

Supplied with long leads for battery and alternator connection. Female spades for alternator and charge sensing, ring connectors for battery. NB this reg/rec should not be used with a lithium-ion battery

 1 in stock

Brand new budget starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016 Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Get a discount of £20 on this item if you part exchange your existing faulty Valeo or Bosch starter motor.

 1 in stock

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Combined regulator rectifier to replace separate items on Bosch equipped models. See our wiring instructions page for help installing this reg/rec.

Includes harness extension with 6 spade connector block. NB this reg/rec should not be used with a lithium-ion battery

 Availability varies on this part, check availability

Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Coil clamp for round 12 volt coils

2 required per bike. No longer available new, call us to order used coil clamps

 Sorry, this part is no longer available.